Table of Contents
The root directory for the C++ distribution is named qpidc-0.4. The README file in that directory gives instructions for building the broker and client libraries. In most cases you will do the following:
[qpidc-0.4]$ ./configure [qpidc-0.4]$ make
Once you have built the broker and client libraries, you can start the broker from the command line:
[qpidc-0.4]$ src/qpidd
Use the --daemon option to run the broker as a daemon process:
[qpidc-0.4]$ src/qpidd --daemon
You can stop a running daemon with the --quit option:
[qpidc-0.4]$ src/qpidd --quit
You can see all available options with the --help option
[qpidc-0.4]$ src/qpidd --help
The qpidd broker requires you to set a data directory or specify --no-data-dir (see help for more details). The data directory is used for the journal, so it is important when reliability counts. Make sure your process has write permission to the data directory.
The default location is
/lib/var/qpidd
An alternate location can be set with --data-dir
Note that when qpidd starts it creates a lock file is data directory are being used. If you have a un-controlled exit, please mail the trace from the core to the dev@qpid.apache.org mailing list. To clear the lock run
./qpidd -q
It should also be noted that multiple brokers can be run on the same host. To do so set alternate data directories for each qpidd instance.
Each option that can be specified on the command line can also be specified in a configuration file. To see available options, use --help on the command line:
./qpidd --help
A configuration file uses name/value pairs, one on each line. To convert a command line option to a configuration file entry:
a.) remove the '--' from the beginning of the option. b.) place a '=' between the option and the value (use yes or true to enable options that take no value when specified on the command line). c.) place one option per line.
For instance, the --daemon option takes no value, the --log-to-syslog option takes the values yes or no. The following configuration file sets these two options:
daemon=yes log-to-syslog=yes
Yes, all the clients work with the C++ broker; it is written in C+, but uses the AMQP wire protocol. Any broker can be used with any client that uses the same AMQP version. When running the C+ broker, it is highly recommended to run AMQP 0-10.
Note that JMS also works with the C++ broker.
The PLAIN authentication is done on a username+password, which is stored in the sasldb_path file. Usernames and passwords can be added to the file using the command:
saslpasswd2 -f /var/lib/qpidd/qpidd.sasldb -u <REALM> <USER>
The REALM is important and should be the same as the --auth-realm option to the broker. This lets the broker properly find the user in the sasldb file.
Existing user accounts may be listed with:
sasldblistusers2 -f /var/lib/qpidd/qpidd.sasldb
NOTE: The sasldb file must be readable by the user running the qpidd daemon, and should be readable only by that user.
On Windows, the users are authenticated against the local machine. You should add the appropriate users using the standard Windows tools (Control Panel->User Accounts). To run many of the examples, you will need to create a user "guest" with password "guest".
If you cannot or do not want to create new users, you can run without authentication by specifying the no-auth option to the broker.
The easiest way to get a full listing of the broker's options are to use the --help command, run it locally for the latest set of options. These options can then be set in the conf file for convenience (see above)
./qpidd --help
Usage: qpidd OPTIONS
Options:
-h [ --help ] Displays the help message
-v [ --version ] Displays version information
--config FILE (/etc/qpidd.conf) Reads configuration from FILE
Module options:
--module-dir DIR (/usr/lib/qpidd) Load all .so modules in this directory
--load-module FILE Specifies additional module(s) to be loaded
--no-module-dir Don't load modules from module directory
Broker Options:
--data-dir DIR (/var/lib/qpidd) Directory to contain persistent data generated by the broker
--no-data-dir Don't use a data directory. No persistent
configuration will be loaded or stored
-p [ --port ] PORT (5672) Tells the broker to listen on PORT
--worker-threads N (3) Sets the broker thread pool size
--max-connections N (500) Sets the maximum allowed connections
--connection-backlog N (10) Sets the connection backlog limit for the
server socket
--staging-threshold N (5000000) Stages messages over N bytes to disk
-m [ --mgmt-enable ] yes|no (1) Enable Management
--mgmt-pub-interval SECONDS (10) Management Publish Interval
--ack N (0) Send session.ack/solicit-ack at least every
N frames. 0 disables voluntary ack/solitict
-ack
Daemon options:
-d [ --daemon ] Run as a daemon.
-w [ --wait ] SECONDS (10) Sets the maximum wait time to initialize the
daemon. If the daemon fails to initialize, prints
an error and returns 1
-c [ --check ] Prints the daemon's process ID to stdout and
returns 0 if the daemon is running, otherwise
returns 1
-q [ --quit ] Tells the daemon to shut down
Logging options:
--log-output FILE (stderr) Send log output to FILE. FILE can be a file name
or one of the special values:
stderr, stdout, syslog
-t [ --trace ] Enables all logging
--log-enable RULE (error+) Enables logging for selected levels and component
s. RULE is in the form 'LEVEL+:PATTERN'
Levels are one of:
trace debug info notice warning error critical
For example:
'--log-enable warning+' logs all warning, error
and critical messages.
'--log-enable debug:framing' logs debug messages
from the framing namespace. This option can be
used multiple times
--log-time yes|no (1) Include time in log messages
--log-level yes|no (1) Include severity level in log messages
--log-source yes|no (0) Include source file:line in log messages
--log-thread yes|no (0) Include thread ID in log messages
--log-function yes|no (0) Include function signature in log messages
By default the broker will load all the modules in the module directory, however it will NOT display options for modules that are not loaded. So to see the options for extra modules loaded you need to load the module and then add the help command like this:
./qpidd --load-module libbdbstore.so --help
Usage: qpidd OPTIONS
Options:
-h [ --help ] Displays the help message
-v [ --version ] Displays version information
--config FILE (/etc/qpidd.conf) Reads configuration from FILE
/ .... non module options would be here ... /
Store Options:
--store-directory DIR Store directory location for persistence (overrides
--data-dir)
--store-async yes|no (1) Use async persistence storage - if store supports
it, enables AIO O_DIRECT.
--store-force yes|no (0) Force changing modes of store, will delete all
existing data if mode is changed. Be SURE you want
to do this!
--num-jfiles N (8) Number of files in persistence journal
--jfile-size-pgs N (24) Size of each journal file in multiples of read
pages (1 read page = 64kiB)