# This file -  Makefile.base-vars - together with the file Makefile.base-rules,
# make up a reusable buildsystem for DocBook XML books.
# The split into two files is required because of the nature of Make variables:
# In the case of variables used in commands, expansion occurs when the commands
# are executed, so values can be overridden by defining a new value after the
# rule definition - BUT in the case of variables used to specify targets and
# sources, expansion occurs when Make parses the rule.  Therefore, any override
# must take place BEFORE the rule definition.  Since this Makefile fragment
# wishes to both provide defaults and allow overriding of target and source
# file names, it is necessary to place the default variable definitions in
# one file, and the rules in another, so that overrides may be specified
# after the defaults, but before the rules - like this:
#
#   include ../tools/Makefile.base-vars
#   NAME = my-book
#   DIR = my-book-dir
#   include ../tools/Makefile.base-rules
#
# Note that this is a Makefile fragment intended for inclusion.  As a result,
# all relative paths contained within are relative to including Makefile's
# directory, not to this fragment's directory.  The TOOLS_DIR and DIR variables
# should be overridden if necessary to ensure proper paths are used.

# Paths which you may wish to customize:
XSLTPROC = xsltproc
XMLLINT = xmllint
INSTALL_DIR = $(DESTDIR)/usr/share/doc/OVERRIDE_ME_WITH_SOMETHING_SUITABLE
INSTALL_DATA = cp -r
MKDIR = mkdir -p
SVNVERSION = svnversion

# You should not normally need to edit anything below here.
SHELL = /bin/sh

NAME = OVERRIDE_ME_WITH_THE_SHORT_FILESYSTEM_NAME_OF_YOUR_BOOK
DIR = .
IMAGES =
TOOLS_DIR = ../tools
OUTNAME = $(NAME)

HTML_CHUNK_DIR = $(DIR)/html-chunk
HTML_TARGET = $(DIR)/$(OUTNAME).html
# In the HTML chunk build, index.html is created last, so serves as an 
# acceptable timestamp file for the entire multi-file output.
HTML_CHUNK_TARGET = $(HTML_CHUNK_DIR)/index.html
ARCH_CMD = tar -jcvf
ARCH_EXT = .tar.bz2
HTML_ARCH_BASENAME = $(OUTNAME)-html
HTML_CHUNK_ARCH_BASENAME = $(OUTNAME)-html-chunk
HTML_ARCH_TARGET = $(DIR)/$(HTML_ARCH_BASENAME)$(ARCH_EXT)
HTML_CHUNK_ARCH_TARGET = $(DIR)/$(HTML_CHUNK_ARCH_BASENAME)$(ARCH_EXT)
PDF_TARGET = $(DIR)/$(OUTNAME).pdf
PS_TARGET = $(DIR)/$(OUTNAME).ps
FO_TARGET = $(DIR)/$(OUTNAME).fo
XML_SOURCE = $(DIR)/$(NAME).xml
VERSION_SOURCE = $(DIR)/version.xml
ALL_SOURCE = $(DIR)/*.xml
STYLESHEET = $(DIR)/styles.css
INSTALL_SUBDIR = $(INSTALL_DIR)/$(NAME)

ENSURE_XSL = if ! test -e "$(TOOLS_DIR)/xsl"; \
	     then $(TOOLS_DIR)/bin/find-xsl.py; fi
IFIMAGES = if test -n "$(IMAGES)"; then
ENDIF = ; fi

# Customization hooks for xsltproc options
HTML_XSLTPROC_OPTS = 
FO_XSLTPROC_OPTS =
# FO example: --stringparam page.height 9in --stringparam page.width 6.4in

# Uncomment the following line if you'd like to print on A4 paper
# FO_XSLTPROC_OPTS = --stringparam paper.type A4

# Override in locale-specific Makefile to localize the word in the 
# auto-generated version file.
L10N_REVISION = Revision