#!/bin/sh

#
# Licensed to the Apache Software Foundation (ASF) under one
# or more contributor license agreements.  See the NOTICE file
# distributed with this work for additional information
# regarding copyright ownership.  The ASF licenses this file
# to you under the Apache License, Version 2.0 (the
# "License"); you may not use this file except in compliance
# with the License.  You may obtain a copy of the License at
# 
#   http://www.apache.org/licenses/LICENSE-2.0
# 
# Unless required by applicable law or agreed to in writing,
# software distributed under the License is distributed on an
# "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
# KIND, either express or implied.  See the License for the
# specific language governing permissions and limitations
# under the License.
#

# Test reliability of the replication feature in the face of link
# failures:
srcdir=`dirname $0`
source ./test_env.sh

trap stop_brokers EXIT

fail() {
    echo $1
    exit 1
}

stop_brokers() {
    if [[ $BROKER_A ]] ; then
        ../qpidd --no-module-dir -q --port $BROKER_A
        unset BROKER_A
    fi      
    if [[ $NODE_1 ]] ; then
        ../qpidd --no-module-dir -q --port $NODE_1
        unset NODE_1
    fi
    if [[ $NODE_2 ]] ; then
        ../qpidd --no-module-dir -q --port $NODE_2
        unset NODE_2
    fi
    if [ -f cluster.ports ]; then
    	rm cluster.ports
    fi
}

start_brokers() {
    #start single node...
    BROKER_A=`../qpidd --daemon --port 0 --no-data-dir --no-module-dir --auth no --log-enable info+` || fail "BROKER_A failed to start"

    #...and start cluster
    $srcdir/start_cluster 2 || fail "Could not start cluster"
    NODE_1=$(head -1 cluster.ports)
    NODE_2=$(tail -1 cluster.ports)
    test -n "$NODE_1" || fail "NODE_1 failed to start"
    test -n "$NODE_2" || fail "NODE_2 failed to start"
}

setup() {
    #create exchange on both cluster and single broker
    $PYTHON_COMMANDS/qpid-config -a "localhost:$BROKER_A" add exchange direct test-exchange
    $PYTHON_COMMANDS/qpid-config -a "localhost:$NODE_1" add exchange direct test-exchange

    #create dynamic routes for test exchange
    $PYTHON_COMMANDS/qpid-route dynamic add "localhost:$NODE_2" "localhost:$BROKER_A" test-exchange
    $PYTHON_COMMANDS/qpid-route dynamic add "localhost:$BROKER_A" "localhost:$NODE_2" test-exchange

    #create test queue on cluster and bind it to the test exchange
    $PYTHON_COMMANDS/qpid-config -a "localhost:$NODE_1" add queue test-queue
    $PYTHON_COMMANDS/qpid-config -a "localhost:$NODE_1" bind test-exchange test-queue to-cluster

    #create test queue on single broker and bind it to the test exchange
    $PYTHON_COMMANDS/qpid-config -a "localhost:$BROKER_A" add queue test-queue
    $PYTHON_COMMANDS/qpid-config -a "localhost:$BROKER_A" bind test-exchange test-queue from-cluster
}

run_test_pull_to_cluster_two_consumers() {
    #start consumers on each of the two nodes of the cluster
    ./receiver --port $NODE_1 --queue test-queue --credit-window 1 > fed1.out.tmp &
    ./receiver --port $NODE_2 --queue test-queue --credit-window 1 > fed2.out.tmp &

    #send stream of messages to test exchange on single broker
    for i in `seq 1 1000`; do echo Message $i >> fed.in.tmp; done
    ./sender --port $BROKER_A --exchange test-exchange --routing-key to-cluster --send-eos 2 < fed.in.tmp

    #combine output of the two consumers, sort it and compare with the expected stream
    wait
    sort -g -k 2 fed1.out.tmp fed2.out.tmp > fed.out.tmp
    diff fed.in.tmp fed.out.tmp || fail "federated link to cluster failed: expectations not met!"
        
    rm -f fed*.tmp #cleanup
}

run_test_pull_to_cluster() {
    #send stream of messages to test exchange on single broker
    for i in `seq 1 1000`; do echo Message $i >> fed.in.tmp; done
    ./sender --port $BROKER_A --exchange test-exchange --routing-key to-cluster --send-eos 1 < fed.in.tmp

    #consume from remaining node of the cluster
    ./receiver --port $NODE_2 --queue test-queue > fed.out.tmp

    #verify all messages are received
    diff fed.in.tmp fed.out.tmp || fail "federated link to cluster failed: expectations not met!"
        
    rm -f fed*.tmp #cleanup
}

run_test_pull_from_cluster() {
    #start consumer on single broker
    ./receiver --port $BROKER_A --queue test-queue --credit-window 1 > fed.out.tmp &

    #send stream of messages to test exchange on cluster
    for i in `seq 1 1000`; do echo Message $i >> fed.in.tmp; done
    ./sender --port $NODE_2 --exchange test-exchange --routing-key from-cluster --send-eos 1 < fed.in.tmp

    #verify all messages are received
    wait
    diff fed.in.tmp fed.out.tmp || fail "federated link from cluster failed: expectations not met!"
        
    rm -f fed*.tmp #cleanup
}


if test -d ${PYTHON_DIR}; then
    . $srcdir/ais_check

    rm -f fed*.tmp #cleanup any files left from previous run
    start_brokers
    echo "brokers started"
    setup
    echo "setup completed"
    run_test_pull_to_cluster_two_consumers    
    echo "federated link to cluster verified"
    run_test_pull_from_cluster    
    echo "federated link from cluster verified"
    if [[ $TEST_NODE_FAILURE ]] ; then
        #kill first cluster node and retest
        kill -9 $(../qpidd --check --port $NODE_1) && unset NODE_1
        echo "killed first cluster node; waiting for links to re-establish themselves..."
        sleep 5
        echo "retesting..."
        run_test_pull_to_cluster
        echo "federated link to cluster verified"
        run_test_pull_from_cluster    
        echo "federated link from cluster verified"    
    fi
fi